Electrical Tips, News & DIY Guides
What Is a Battery? A battery is a device that converts chemical energy into electrical energy and supplies current for use.A chemical reaction occurs between the two electrodes and the electrolyte inside, producing EMF (Electromotive Force).When the battery is connected to a closed circuit, electrons begin to flow, and electric current is produced.From small watches … Read more
What is the Cooling of Transformers? Cooling of transformers is the process by which the heat generated in the transformer windings and core is safely removed to prevent overheating, insulation damage, and failure.This heat is mainly produced due to I²R losses, hysteresis losses, and eddy-current losses. Transformer Cooling Methods The main methods used to cool … Read more
Lightning Earthing vs Normal Earthing – Deep Practical Guide. Lightning Earthing and Normal Earthing differ mainly in the type of current they handle. Normal Earthing is used to discharge low-voltage fault currents using G.I./copper rods with charcoal–salt filling, while Lightning Earthing is specially designed to handle high-energy lightning surges using thick copper rods, bentonite compounds, … Read more
How to construct an earthing pit correctly, and which materials and techniques are most effective? Answer:The most important factors in earthing pit construction are: Introduction With correct construction and regular maintenance, you can ensure a low-resistance, long-lasting, and safe earthing system. Earthing systems play an extremely important role in electrical safety.A properly constructed earthing pit … Read more
Types of Energy and Forms of Energy are the different ways in which energy exists in nature and is used to perform work. Energy exists in various forms, including mechanical, Thermal, Chemical, Electrical, Nuclear, Light, Sound, and Magnetic Energy. Simple Meaning: Introduction Energy is the “hidden power” behind every civilization — the force that runs … Read more
What is the correct Earthing Installation Cost, and which method is the best? Answer:The cost of earthing depends directly on the type, material, soil condition, and depth. With proper installation, correct material selection, and periodic maintenance, you can build a low-resistance and long-lasting earthing system that protects against electric shocks and keeps your equipment safe. … Read more
How to Reduce Earthing Resistance The most effective way to reduce earthing resistance is to increase soil conductivity, use high-quality backfill compounds (such as Bentonite/GEM), install larger and deeper electrodes, and connect multiple rods in parallel. Increasing moisture, using charcoal–salt layering, chemical earthing rods, selecting the right location, and ensuring corrosion-free, tight connections also help … Read more
What Is Earthing Resistance? Earthing resistance is the opposition offered by an electrode while dissipating current into the ground. Its main formula is: R = ρ / 2πL (ln(4L/d) – 1). The ideal value for homes is 1–5 Ω, and for industries, it is less than 1 Ω̣. Introduction Earthing resistance is one of the … Read more
GI Earthing vs Copper Earthing: The main difference is that GI earthing (Galvanized Iron) is a low-cost option but prone to corrosion with medium conductivity, while constant Copper earthing provides very high conductivity, long lifespan, and stable low resistance. GI earthing is ideal for homes and small loads, whereas Copper earthing is recommended for industries, … Read more
Pipe Earthing vs Plate Earthing: The main difference is that Pipe Earthing uses a vertical G.I. pipe and is low-cost, suitable for homes and small loads, while Plate Earthing uses a Copper or G.I. plate at a deeper depth, offering very low resistance and long life for heavy loads. Pipe earthing is ideal for domestic … Read more
The main difference between Chemical Earthing vs Conventional Earthing lies in soil treatment and resistance performance. In Conventional Earthing, a G.I. pipe or copper plate is installed at a depth of 2–3 meters with a charcoal–salt mixture, and it requires regular watering. Because of this, its resistance generally remains around 5–10 Ω. In Chemical Earthing, … Read more
What is earthing? Earthing connects metal parts of electrical equipment or neutral points to the earth, ensuring human safety, equipment protection, and voltage stabilization during faults or surges. 2. What is grounding? Grounding connects the system neutral to earth, stabilizing system voltage and providing a safe return path for excess or fault current. 3. Difference … Read more
How to Measure Earth Resistance? To measure earth resistance at home, use the 3-point fall-of-potential method with main, current, and potential electrodes. Ensure rods are 3–4 meters deep, properly spaced, and the soil is moist or treated with bentonite. Accurate readings help maintain low-resistance earthing for safety and equipment protection. Why measure earth resistance at … Read more
What are the types of earthing electrodes, and which one is best? Earthing electrodes include GI pipe, Copper pipe, GI plate, Copper plate, Chemical (copper-bonded) rod, and GI/Copper strips.The best electrode depends on soil type and load: For long-lasting and low-resistance earthing, use chemical or copper electrodes, maintain 10–12 ft depth, apply bentonite compound, test … Read more
Why Earthing Fails? Earthing failures mainly occur due to high soil resistance, poor-quality materials, dry pits, corrosion, loose joints, incorrect pit depth, and a lack of testing. To prevent earthing failure, use high-grade electrodes, maintain moisture, apply a bentonite compound, ensure a proper pit distance, perform seasonal testing, and utilize parallel multiple earthing pits to … Read more
1️⃣ What is Pipe Earthing? Answer:Pipe Earthing is an earthing system in which a galvanized iron (G.I.) pipe is installed vertically in the ground to discharge electrical current into the earth safely.It is used in both domestic and industrial installations. 2️⃣ Construction of Pipe Earthing Answer:In Pipe Earthing, a G.I. pipe of 30mm–65mm diameter and … Read more
What is Plate Earthing and why is it used? Plate Earthing is a grounding method in which a metal plate made of copper or G.I. is buried deep in the earth. It provides a low-resistance path for fault current to flow safely into the ground, protecting electrical systems and people from electric shock or damage. … Read more
Q1. What is earthing in an electrical system? Answer:Earthing is the process of connecting the non-current-carrying parts of an electrical system to the ground. It provides a safe path for leakage or fault current, preventing electric shock and protecting equipment. Q2. Why is earthing important? Answer:Earthing ensures the safety of people and electrical appliances. It … Read more
What is a Capacitive Proximity Switch? A Capacitive Proximity Switch is a non-contact sensor that detects the presence or absence of an object by sensing changes in capacitance.It can detect both metallic and non-metallic materials such as plastic, glass, wood, paper, and liquids — making it ideal for industrial automation applications. Construction of Capacitive Proximity … Read more
1. What is a Frequency Response Relay? A Frequency Response Relay is a protective device that operates when the power system frequency deviates from its normal value. It continuously monitors frequency and triggers corrective actions, such as tripping a circuit breaker, whenever the frequency rises or falls beyond preset limits to ensure system stability and … Read more
🧠 1. What is a Latching Relays? A latching relay is an electromagnetic relay that holds its last position even after power is removed, using a mechanical or magnetic latch. ⚙️ 2. Working Principle It has two coils—Set and Reset. The Set coil changes contact position; the Reset coil restores it. The relay stays latched … Read more
What is a DC Series Current Relay? A DC series current relay is a protection device that monitors current flow in a DC circuit. It’s connected in series with the load, and when current exceeds a preset limit, it activates contacts to open or close the circuit—preventing damage from overcurrent. How does a DC Series … Read more
What is a Bimetallic Thermal Overload Relay? A Bimetallic Thermal Overload Relay is a protective device that protects the motor from damage caused by overload or excessive current (overcurrent).It works on the principle of thermal expansion of metals, where the strip bends when heated and breaks the circuit. 🏗️ 2. Construction of Bimetallic Thermal Overload … Read more
What is a Pneumatic Timer? A pneumatic timer is an air-logic timing device that creates a precise time delay using compressed air, without relying on electrical or electronic components.It works by metering airflow into a chamber to delay or sustain an output (NO/NC contact). Because it operates without electricity, it is safe for use in … Read more
What is an Electronic Timer? An Electronic Timer is a device that uses an electronic circuit to generate a time delay.It is generally of the ON-Delay type, meaning that after receiving an input signal, the output becomes active after a certain delay period. How many types of Electronic Timers? There are five main types of … Read more
What is a Buck and Boost Converter? A Buck and Boost Converter is a DC-DC circuit that steps down or steps up input voltage to provide a regulated, efficient, and stable output. What is a Buck Converter? A Buck Converter is a switching regulator that converts a higher DC voltage into a lower DC voltage. … Read more
Superposition Theorem In this article on Superposition Theorem Examples with Solutions, you will learn how to apply the Superposition Theorem step-by-step, understand its mathematical foundation, and solve real numerical problems involving DC, AC (phasor), mixed DC+AC, and dependent-source circuits. 📖 Definition The Superposition Theorem is a fundamental principle that states: 👉 In any linear, bilateral … Read more
Introduction Polarity Test of Transformer – Why and How? Transformers are the backbone of power systems. They step up the voltage for long-distance transmission and step down the voltage for safe utilization. However, when two or more transformers are connected in parallel, even a minor error can lead to serious faults, equipment damage, or fire … Read more
Introduction A transformer is considered the backbone of the power system. It helps transfer electricity safely and efficiently from one voltage level to another. But before any transformer is commissioned in a real power network, certain standard tests are carried out to check its safety and efficiency. The most important of these tests are – … Read more
Introduction Transformers are vital components in electrical power systems, and their safe and efficient operation depends heavily on correct usage as per their design limits. One of the most important aspects that ensures this is transformer ratings. These ratings define the limits within which a transformer can operate without compromising its safety, performance, or efficiency. … Read more
Introduction Transformers are essential electrical machines that require proper testing to ensure reliable operation, efficiency, and safety. Several testing methods are used to analyze transformer performance, such as: 2. Importance of Direct Loading Test on a Transformer Performance Evaluation The Direct Loading Test on a transformer holds special significance because: This test directly measures input … Read more
Introduction A transformer is one of the most vital electrical machines used in power systems. Its primary role is to step up or step down voltage levels, making power transfer more reliable and economical. Transformers ensure smooth and efficient power transmission from generating stations to end users, reducing waste and maintaining system stability. The transformer’s performance … Read more
When a transformer is supplied with a fixed applied voltage at its primary winding, the secondary terminal voltage does not always remain constant. If the magnitude or power factor of the load connected to the secondary side changes, a corresponding change in is observed. This change occurs due to the voltage drops across the winding … Read more
1. Introduction Transformers are vital components in electrical power systems, used to step up or step down voltages efficiently. However, a real transformer is not perfect — it has losses and non-idealities. The equivalent circuit is a simplified model that represents these imperfections, helping engineers analyze and design transformers effectively. 2. What is an Equivalent … Read more
1. Introduction A transformer is a key device in electrical power systems. It moves electrical energy from one circuit to another using electromagnetic induction. In an ideal world, transformers would work perfectly with no losses or voltage drops. But in real life, they have limits. One important factor is leakage reactance. This affects how well … Read more
Operation of Transformer in On-Load Condition To understand the operation of a transformer in load, let us first recall its on-load condition. In the on-load state, when an input voltage is applied across the primary winding, a small on-load current flows. This current establishes a magnetic flux in the transformer core. What is a Transformer? … Read more
Difference Between Ideal and Practical Transformer When it comes to learning about transformers, two terms often pop up: ideal transformer and practical transformer. They sound similar, but there’s a big difference between them. Let’s explore it in a way that’s easy to understand. What is a Transformer? A transformer is an electrical device that transfers … Read more
Understanding the brake test of dc motor: Imagine trying to find out how well a DC motor is working—how much of the electrical power it uses turns into useful mechanical work. One easy and direct way to check this in a lab is by do something called a Brake Test. Let’s break it down in … Read more
Two-Point Starter A two-point starter is used for starting DC series motors. It is a simple device that helps control the starting current to prevent damage to the motor. A Two-Point Starter is a simple device used FOR safely starting a DC series motor. When a motor starts, it can draw a large amount of … Read more
Three-Point Starter A three-point starter is commonly used to safely start DC shunt motors. Just like the two-point starter, it controls the high inrush of current when the motor is switched on. But this one comes with an added feature—overload and no-voltage protection, making it more reliable. What is a Three-Point Starter? The name “three-point” … Read more